The quickest way to clean window and sliding door tracks is dry first, then wet: vacuum out loose dirt with a crevice tool, loosen what is stuck with a stiff brush, then wipe the channels with warm soapy water or a bicarb and vinegar mix and dry them well. A butter knife wrapped in a cloth gets into the corners, and clearing the small drainage holes stops water pooling the next time it rains.
Why tracks matter at an inspection
Consumer Affairs Victoria’s cleanliness guideline lists windowsills free from dust and dirt, and windows (including the outside of ground-floor windows) free from marks, smears, dust and dirt, among its examples of a reasonably clean property. Tracks sit right under the glass, and grit, dead insects and black grime in the channels are easy to spot when an inspector slides a door open.
What you need
- A vacuum with a crevice tool and a brush attachment
- A stiff, narrow brush, such as a grout brush or an old toothbrush
- A butter knife or flat plastic tool, plus a thin cloth to wrap around it
- Cotton buds for corners and drainage holes
- Microfibre cloths and paper towel
- Dishwashing liquid and warm water in a spray bottle
- Bicarb soda and white vinegar (optional, for grime)
- Rubber gloves
Step by step
- Open the window or door fully so you can reach the whole length of the track. Do one side, then slide the panel across and do the other.
- Remove fly screens where they lift out easily, and set them aside to clean separately.
- Vacuum dry debris. Run the crevice tool along each channel. Do this before any liquid goes in, or dust turns to mud.
- Loosen packed dirt. Scrub the channels with the stiff brush, working into the corners, then vacuum again.
- Apply a cleaning solution. Spray warm water with a few drops of dishwashing liquid along the track. For greasy or grimy tracks, sprinkle a thin line of bicarb soda first, then spray lightly with white vinegar. It will fizz and help lift the grime. Leave it for five to ten minutes.
- Scrub and wrap. Scrub again with the brush, then wrap the cloth around the butter knife and run it along the bottom and sides of each channel. Rinse and rewrap the cloth as it gets dirty.
- Clear the corners and drainage holes with cotton buds (details below).
- Wipe with clean water to remove soap or bicarb residue, then dry the track thoroughly with paper towel or a dry microfibre cloth.
- Finish the frame and sill. Wipe the frame, the sill and the bottom edge of the glass, which usually catches drips from the track.
Drainage holes
Many aluminium window and sliding door frames have small drainage slots, usually on the outside face at the bottom of the frame, that let rainwater escape. When they block, water sits in the track and grime builds faster. Gently clear them with a cotton bud or a pipe cleaner, then pour a little water into the track and check it drains out. Do not force sharp objects into the slots, as some have small flaps or covers that can break.
Black marks and mould in tracks
Damp tracks, especially on bathroom windows and shaded sliding doors, can grow mould. For light marks, spray undiluted white vinegar, leave it for about an hour, scrub with the brush, wipe and dry. For heavier growth, use a product labelled for mould on hard surfaces and follow its directions exactly. Ventilate the room and wear gloves.
Never use a bleach-based product in the same session as vinegar or any other acidic cleaner, and never mix bleach with ammonia. Rinse the track with plain water before switching products. If the mould is in silicone or on the ceiling as well, our guide to removing mould from bathroom ceilings and silicone covers those surfaces.
Sliding door tracks
Sliding door tracks are wider and take more foot traffic, so they collect more grit. Follow the same steps, but:
- Vacuum both the inside and outside rails, including the strip under the door where it meets the floor.
- Use a stiffer brush on the outside track, which faces the weather.
- Check the bottom of the door panel itself, where dirt sticks to the rollers’ housing.
- Once dry, slide the door back and forth several times. If it still drags, a light spray of a dry silicone lubricant made for door tracks can help. Avoid oily products, which attract dust.
Fly screens
Lay lift-out screens flat on a towel and vacuum both sides with the brush attachment. Wash them gently with a soft brush and soapy water if they are grimy, rinse with a hose on a light setting and let them dry before refitting. Fixed screens can be vacuumed and wiped in place.
How long it takes
Lightly dusty tracks can take a few minutes per window. Tracks that have not been touched in years, with packed dirt and mould, can take much longer, which is one reason they are often left to the end and then rushed. Doing a few windows a day in the week before you move takes the pressure off cleaning day.
Tracks are one line on the full move-out list in our end of lease cleaning checklist.
Handing the job over
If you would rather leave window tracks, sills and the rest of the property to someone else, Prime Cleaners Melbourne can quote an end of lease clean for your home.
Quick answers
Can I use a pressure washer on outside door tracks?
It is not recommended. High pressure can force water past the seals into the frame or the wall cavity and can damage weather strips. A brush, a vacuum and a spray bottle are slower but safer for tracks.